In the previous article I looked at where additive manufacturing might fit into quantum hardware. Here I want to look at the materials themselves. If you read about three-dimensional superconducting cavities, two metals appear again and again: high-purity aluminium and niobium. They are very different materials, and the reasons each is chosen say a lot about what makes a good cavity.

I am writing as a materials and manufacturing engineer. The physics of cavity quantum electrodynamics is a deep field of its own; my interest is in what the material and the manufacturing route contribute.

What a cavity needs from its metal

A superconducting cavity stores microwave energy in the space inside it. The walls carry microwave currents in a thin surface layer. The longer the energy survives, the more useful the cavity. Performance depends on:

  • Being superconducting at the operating temperature, with margin.
  • Low surface resistance, which depends on the material, its purity and the state of its surface.
  • A clean, smooth, undamaged surface, because the currents flow there.
  • Few seams, or seams placed where currents are low.
  • Low trapped magnetic flux, which depends on how the metal is cooled and shielded.

Aluminium: simple, pure, machinable

Aluminium becomes superconducting at about 1.2 K. That sounds low, but quantum processors operate at around 10 to 20 millikelvin, far below it, so aluminium is comfortably superconducting there.

Its advantages for cavities are practical:

  • It is available in very high purity, often 99.999% and above, at reasonable cost.
  • It machines easily, so complex cavity and coupling geometries can be made with conventional tools.
  • It can be chemically etched to remove the machining-damaged surface layer, which research groups found greatly improves performance.
  • It forms a thin, stable native oxide, and its surfaces are well understood from decades of use in superconducting circuits, where aluminium is the standard material for Josephson junctions.

Work at Yale in the early 2010s showed that carefully etched cavities made from high-purity aluminium could store single microwave photons for around 10 milliseconds, a very long time in this field. That result helped make 3D aluminium cavities a standard building block for cavity-based quantum experiments.

The material lesson is clear: purity and surface preparation matter as much as the geometry. The same shape machined from ordinary aluminium alloy, without etching, performs far worse.

Niobium: the accelerator veteran

Niobium becomes superconducting at about 9.2 K, the highest of the pure elements. It has been the material of choice for superconducting radio-frequency (SRF) cavities in particle accelerators for decades. That industry has developed a huge body of knowledge on how to make niobium cavities with extremely low losses: high-purity niobium sheet, deep drawing and electron-beam welding, electropolishing, high-temperature vacuum heat treatments, and controlled low-temperature bakes.

In 2020, researchers at Fermilab reported that SRF niobium cavities, operated at millikelvin temperatures, could reach photon lifetimes of up to about two seconds. That brought the accelerator community’s know-how directly into quantum research.

Niobium’s challenges are also material ones:

  • Its oxides are complex. Niobium forms several oxides, and the surface oxide layer is a known source of loss at low temperatures and low fields. Removing or controlling that oxide is an active research area.
  • It is harder to machine than aluminium and is usually formed and welded rather than machined from a block.
  • Processing is specialized, and requires the equipment and experience the SRF community has built.

Why both are changing cavity design

Together, these two materials have changed how designers think about cavities in three ways.

From geometry-first to surface-first. Early cavity design focused on shape and coupling. The aluminium and niobium results showed that the surface preparation can matter as much as, or more than, the geometry. Design now has to include how every surface will be etched, polished, heat-treated and kept clean.

Seams matter. Both communities have paid close attention to where joints sit. Designs that keep seams away from regions of high current, or avoid them with clever geometry, perform better.

Materials science moved to the centre. Oxides, hydrogen in niobium, grain boundaries, impurities and surface damage from machining are now discussed in quantum hardware papers. That makes the field more interesting for people like me, who come from materials and process engineering.

Where manufacturing engineers can contribute

From my side of the fence, the open questions look familiar:

  • Machining damage and how to remove it. How deep is the damaged layer, and what is the most reliable way to remove it on complex geometry?
  • Surface chemistry control through etching, polishing, baking and storage.
  • Joining with low-loss seams, or geometries that avoid them.
  • Process repeatability, because a quantum computer needs many good cavities, not one record result.
  • Additive routes for future geometries, provided purity and surface can be brought close enough to the best conventional parts. The gap is still large, especially for internal surfaces, but it is the kind of gap materials engineering has closed before.

Pure aluminium and niobium are teaching quantum hardware what metallurgy has always known: performance lives in purity, in microstructure and, above all, in the surface.

Further reading

  • Reagor, M. et al. (2013). Reaching 10 ms single photon lifetimes for superconducting aluminum cavities. Applied Physics Letters 102, 192604.
  • Romanenko, A. et al. (2020). Three-dimensional superconducting resonators at T < 20 mK with photon lifetimes up to τ = 2 s. Physical Review Applied 13, 034032.
  • Padamsee, H. RF Superconductivity: Science, Technology and Applications. Wiley-VCH.